Что такое part 145 в авиации
Независимые аудиты организаций занимающихся техническим обслуживанием воздушных судов
Экспертная команда, формируемая под конкретную задачу составляет программу аудита на основе применяемой нормативной базы, отвечающей целям аудита. Программа одобряется заказчиком и реализуется экспертной командой. Аудит проводится на базе Вашего предприятия в сроки установленные контрактом и программой аудита.
Какая применяется методическая основа для данной услуги?
Для организаций по ТОиР выполняющих техническое обслуживание (ТО) ВС Российской регистрации.
Аудиты проводятся на основании следующих основных Федеральных Авиационных Правил:
— ФАП-285 (Техническое обслуживание ВС).
Для организаций по ТОиР выполняющих ТО ВС Европейской регистрации:
— EASA Part-145 (Aircraft Maintenance).
Для организаций по ТОиР выполняющих ТО ВС регистрации British Overseas Territories:
— OTAR Part 145 (Aircraft Maintenance Organisation Approval).
— OTAR Part 43 (General Maintenance Requirements).
Какой ожидаемый результат?
По результатам вы получите подробный аудиторский отчет о соответствии Вашей организации по ТО установленным требованиям и рекомендации по действиям, которые необходимо выполнить для достижения соответствия требованиям.
Для чего можно использовать результат услуги?
Результаты независимого аудита можно использовать:
— как рекомендации по подготовке к проведению обязательных проверок со стороны авиационных властей;
— при расширении сферы деятельности организации по ТО;
— для определения поставщика услуг по ТО для Ваших ВС;
— для повышения качества функционирования процессов в Вашей организации.
Что такое part 145 в авиации
п.с. в сети нашел учебный центр АМИКОН, кому то он уже помог?
Достойная контора. Многие компании через него прошли.
В Приказ по ошибке не внесли.
Есть у него одобрение САА РФ.
Где-то у меня есть скан ответа им из Росавиации.
Только парню это одобрение зачем? Он для EASA ищет. РФ туда не пустят, много языков придётся признавать официальными 😉
«слушай, а в германии разве не учат такому?»
учат, но за свой счет очень дорого, а компания пока не готова эту учебу мне оплатить.
Причём тут межправ.
И тутЬ ничего нетутЬ:
3.3. Организации, в которых производится подготовка инженерно-технического персонала, как правило, рекомендуются изготовителем ВС и должны быть сертифицированы авиационными властями государства изготовителя АТ или государства дислокации Организации и одобрены ДВТ для выполнения такого обучения. Одобрение проводится по результатам аудиторской проверки Обучающей организации специалистами-экспертами ДВТ. Аудиторская проверка выполняется за счет средств эксплуатанта, владельца ВС или обучающей организации.
Вот ДВ-130 и процитировал.
. плановые аудиты Парт-145 организаций в ЕВРОПЕ
Периодичность инспекций EASA указана в PART-145, если не ошибаюсь, но никак не срок действия Сертификата, он бессрочен. Потому и спрашиваю, аналогия с одобрением неприемлема.
а оплачивали эти курсы Вы сами или компания? Интересно в какую сумму это удовольствие обошлось.
Тема о PART-147 EASA у Амикона, бесспорно.
. САА стран ЕС делает аудиты по разным критериям, например если расширяете свои возможности и т.д.
А вот приказ не о допуске УЦ к подготовке персонала, а об опубликовании одобренных центров.
Вообще, возникает огромное сомнение в наличии полномочий у Федерального агентства что-то одобрять. Можете указать норму, позволяющую такое делать Росавиации?
Вообщем не делайте ошибок сами и не советуйте их делать своим коллегам, экономьте деньги своей компании и старайтесь чтобы они (деньги) оставались внутри нашей страны! Тем более, что уже есть достойные примеры у нас в РФ.
Получение сертификата соответствия по правилам EASA является на сегодня одной из наиболее востребованных задач для российских компаний, связанных с эксплуатаций воздушных судов иностранного производства и производителей авиационной техники. В то же время, эта задача представляется довольно сложной в связи с отсутствием у компаний опыта взаимодействия с авиационными властями EASA и тем, что вся базовая документация представлена только на английском языке. Наши эксперты помогут решить задачи по получению сертификата на выполнение технического обслуживания (PART-145), Инженерно-технологического обеспечения (PART-M), обучения персонала (PART-147) в минимально возможные сроки и подготовят Ваш персонал к дальнейшей работе в рамках полученного сертификата соответствия. Так же наши эксперты выполняю работы по подготовки предприятий к сертификации по правилам EASA PART-21, оценка возможности получения сертификатов типа в соответствии с требованиями EASA Certification Specifications (CS-23, CS-25, CS-27, CS-29 и т.д.).
Подготовка к получению сертификатов EASA PART-21, PART-M, PART-145, состоит из нескольких этапов, которые могут реализовываться последовательно или параллельно, в зависимости от возможностей и степени подготовленности компании.
На каждом этапе наши консультанты окажут Вам следующие услуги:
Этап проведения предварительного аудита:
— Проведение предварительного аудита.
— Разработка плана мероприятий по подготовке Заказчика к сертификации.
Этап подачи заявки для первоначального одобрения:
— Консультация и оказание помощи в подборе нормативной базы по сертификационным требованиям по авиационным правилам EASA.
— Консультация и методическая помощь в подготовке и оформлении содержательной части заявочной документации EASA Form 2, EASA Form 4
Этап подготовки на соответствие сертификационным требованиям EASA производственно-технической базы:
— Консультация по нормативным требованиям, предъявляемым к производственным помещения и участкам в соответствии с требованиями EASA.
— Оценка достаточности уровня соответствия производственных и архивных помещений, участков и площадей в отношении заявляемой сферы деятельности.
Этап подготовки персонала в соответствии с требованиями EASA:
— Консультация по требованиям к структуре, подготовке и мере ответственности персонала и способам демонстрации поддержания квалификации.
— Консультация и помощь в способах демонстрации достаточности человеческих ресурсов для заявляемой сферы деятельности.
— Консультация по требованиям и способам достижения соответствия к сертифицирующему персоналу, категорийности персонала, доказательной документации имеющегося опыта, по содержанию, хранению и предъявлению персональных данных, по возможности замещения и делегирования полномочий.
Этап подготовки на соответствие требованиям EASA по наличию и соответствию инструмента и оборудования:
— Консультация по требованиям к получению, учету, хранению и маркировке инструмента и оборудования.
Этап подготовки к демонстрации соответствия требованиям EASA, предъявляемым к компонентам и материалам:
— Консультация по методам выбора Поставщиков и демонстрации их соответствия.
— Консультация по требованиям, предъявляемым к хранению материалов и компонентов, к сопроводительной документации при поставке, способам и методам ведения и оформления внутренней документации, к порядку учета выдачи и приема материалов и компонентов.
Этап подготовки к демонстрации наличия эксплуатационно-технической документации и ведения записей по ТО:
— Консультация по вопросам организации работы с ЭТД, поддержанию ЭТД путем учета временных и постоянных ревизий, организации доступа ИТП к ЭТД, ведения записей по техническому обслуживанию, организации хранения данных записей.
Этап подготовки подразделения производства и планирования к работе в соответствии с требованиями EASA:
— Консультация по выполнению требований в части взаимодействия подразделений.
— Консультация по способам демонстрации планирования человеческих ресурсов, доступности производственных площадей, инструмента, оборудования и материалов при ТО, учета выполнения критических задач при ТО.
Этап создания внутренней руководящей документации:
— Консультация и методическое сопровождение написания Maintenance Organisation Exposition (MOE), Continuous Airworthiness Management Exposition (CAME), Maintenance Training Organisation Exposition (MTOE).
— Консультация в разработке внутренних процедур, обеспечивающих выполнение требований EASA.
— Консультация и методическая помощь в разработке внутренних форм учетной и отчетной документации, а также форм рабочей документации при ТО.
— Консультации по разработке учебных программ.
— Консультация и помощь во взаимодействии с компетентными авиационными властями EASA;
— Участие в комиссии EASA и отстаивание интересов Заказчика перед аудиторами EASA.
PART-145, PART-147
Является основным и престижным сертификатом, выдаваемым организациям по техническому обслуживанию воздушных судов. Сертификат даёт право выполнять ТО на самолётах Европейской регистрации, либо регистрации других государств, расположенных вне Евросоюза, но признающих требования Europe Aviation Safety Agency (EASA) в отношении технического обслуживания ВС. В приложении к данному сертификату отражены все виды ТО, которые организация имеет право выполнять, с указанием типов воздушных судов. Для продления срока действия EASA Part-145 Холдинг «Инжиниринг» проходит аудит Европейских авиационных властей не реже одного раза в год.
Bermuda Aircraft Maintenance Organization Approval Certificate (BDCA)
Документ, подтверждающий соответствие организации требованиям EASA PART-145 по техническому обслуживанию воздушных судов Бермудской регистрации. Бермудские авиационные власти проводят аудит не реже одного раза в 2 года.
Bermuda Approval Certificate Continued Airworthiness
Холдинг «Инжиниринг» имеет право выполнять работы по поддержанию лётной годности (ПЛГ) ВС Бермудской регистрации, что подтверждено сертификатом Bermuda Approval Certificate Continued Airworthiness. Данный сертификат даёт право на ведение статусов ПЛГ (отслеживание бюллетеней, директив лётной годности, ресурсов и сроков службы компонентов).
Одобрение Российских авиационных властей
Холдинг «Инжиниринг» имеет на все базы ТО и ЛСТО одобрение от Российских авиационных властей на выполнение технического обслуживания воздушных судов Российских авиакомпаний на территории Российской Федерации.
Нам важно ваше мнение! Был ли полезен опубликованный материал? Да | Нет
Part-145
Part-145: General
Is Part-M applicable to approved Part-145 organisations?
Yes, in addition to the Part-M or Part-ML provisions directly referred to in Part-145 (such as reference to point M.A.304 or ML.A.304 in 145.A.48), certain other requirements laid down in Part-M or Part-ML should also be considered by these organisations. Guidance on this subject is given in ‘GM Article 4(1)’.
Was this helpful?
What does the term ‘occasional’ mean in 145.A.75(c)?
Within the privilege described in 145.A.75(c) an aircraft maintenance organisation (AMO) may perform line maintenance activity (Part-145) in other-than-approved locations, provided it is considered as ‘occasional’. There is no formal definition of ‘occasional’ in the regulation, AMC and GM, but this privilege should be used to support an operator with which the AMO is already in contractual relation, when this operator needs line maintenance service for a short period at a new location due to a special occasion or particular reason (e.g. one-time flights, short term contracts/flight destination, flight schedule changes, special event at a particular location such as European athletics championship in Berlin, 6-12 August 2018, etc.) or the owner needs supporting maintenance service for a short period at a new location due to a special occasion or particular reason.
Subject to the approval by the Competent Authority, the maintenance organisation should develop in the MOE (e.g. Chapter 2.24 Reference to Specific Maintenance Procedures) the generic procedures to be followed in such a case: how to assess whether the maintenance can be performed, availability of tools/ equipment/ material/ components/ maintenance data, staff, adequacy of the facilities, environmental conditions, quality system, record keeping, need to report these cases to the competent authority, etc. In addition, the procedure should include the criteria (e.g. maximum service duration without gap in the continuity; limitation in the repetition of the need* at one given location) to classify the activity as ‘occasional line maintenance’.
* In principle, the repetitive use of this privilege at the same location should not be considered, and for repetitive needs, an approved line station should normally be established at that location.
Was this helpful?
How to easily update the “EASA Form 1 – MF/145 Issue 2” to “EASA Form 1 – MF/CAO/145 Issue 3”?
Purpose of the FAQ
This FAQ is intended to recommend the industry and national competent authority (NCA) an easy way to implement the ‘EASA Form 1 Issue 3’, applicable from 24.03.2020, by the Maintenance organisations.
Description of the issue
The Regulation (EU) 2019/1383 updated the Appendix II to Annex I (Part-M) — Authorised Release Certificate — EASA Form 1 by changing the footer of the form in order to add the reference of the Part-CAO.
Some organisations may still have in stock hardcopies of EASA Form 1 Issue 2.
In such case, due to the fact that there is no change in the content of the EASA Form 1 or/and in its completion methodology, for the Part-145 and Part-M, Subpart F approved organisations, the change can be done by:
Was this helpful?
How did you install a Commercial Off-The-Shelf (COTS) equipment without EASA form-1? How do you arrange Part-145 side actually?
Please check for the answer published here.
Was this helpful?
Quality system
Does the Part-145 or Part-CAO quality system need to be subject to monitoring?
Yes, the quality system is part of the activities of the Part-145 organisation and therefore it should be monitored.
Point 145.A.65 (c) or CAO.A.100 (b) (1) requires that the quality system monitors that the activities are (being) performed in accordance with the approved procedures. The quality system procedures are included within these approved procedures. This implies that quality system must be subject to audits and the Part-145 or Part-CAO organisation audit programme/plan needs to reflect this.
Besides that, the audits of the quality system shall satisfy the requirement of independent audits. This is further explained in AMC 145.A.65(c)(1) point 11: the independence of the audits should be established by always ensuring that audits are carried out by personnel not responsible for the functions, procedures or products being checked. So, the quality manager cannot audit the quality system in terms of independence of the audit. For Part-CAO this subject is explained in AMC1 CAO.A.100(b).
Therefore, to audit the quality system, it is acceptable to:
The way the quality system is going to be audited has to be described in the MOE or CAE and approved by the competent authority.
Was this helpful?
Certification of maintenance
With respect to blend out repairs, is it required to record the depth and area dimensions of material removed during a blend out repair or is it sufficient to simply record that the damage has been repaired as per the SRM?
Yes, the dimensions of the damage and the removed/remaining material should be recorded. This is a very important information in order to assess whether further damage (adjacent or at the same spot) at a later stage would be allowable or not. In addition, it is a safeguard measure in order to be able to determine, during audits, whether the person correctly determined that the damage was within limits.
Was this helpful?
Can the subcontractor of a Part-145 or Part-CAO organisation release maintenance?
One of the fundamentals of subcontracting activities is that, during such maintenance, the Part-145 approval is extended to include the subcontractor activities. Subcontracting can be done only if the Part-145 has approved procedures to do it (145.A.75(b)) and the MOE is amended to reflect this new subcontractor.
A certificate of release to service can be issued by a person from the subcontractor who has received a certification authorisation from the Part-145 organisation in accordance with the certification authorisation procedure of the MOE including the assessment of competence.
The certificate of release to service and the EASA Form 1 will always be issued under the maintenance organisation approval reference.
For maintenance by Part-CAO the situation is different. Only ‘specialised services’ (e.g. NDT) can be subcontracted to another organisation, in accordance with the appropriate procedure set out in the CAE and approved by the competent authority (CAO.A.095(a)(2)). In accordance with AMC1 CAO.A.025 the procedure should be part of chapter B.7 ‘Subcontracting’.
A certificate of release to service can be issued by a person from the other organisation who has received a certification authorisation from the CAO in accordance with the certification authorisation procedure of the CAE.
The certificate of release to service will always be issued under the CAO approval reference.
Was this helpful?
Release to service of NDT tasks by Part-145 or Part-CAO organisations
This answer is separated in two tables. One table is for organisation holding a Part-145 approval and the second table is for organisations holding a Part-CAO approval.
Part-145:
Certifying staff required
General Release procedure
Release procedure for an NDT inspection
The release of the aircraft maintenance carried out under A class rating has to be performed by certifying staff holding a Part-66 licence. (B1 or B3 or C or L certifying staff under the organisation’s A rating.)
Licencing of personnel has to follow Part-66 regulation.
The release is either on the aircraft technical log or issuing an aircraft release to service statement.
The release of the engine maintenance carried out under B class rating has to be performed by engine’s certifying staff.
The certifying staff is qualified following the procedures established by the organisation in compliance with the competent authority requirements. Part-66 licence is not required.
The release of works performed under class B is done on an EASA Form 1 (or by means of an internal release document when this component is for the organisation’s own use and the organisation has in place the related internal procedures in the MOE).
A Part-145 organisation holding a B rating approval on a particular engine type and having in its approved scope of work NDT inspections for this engine type.
This organization needs to have “engine” certifying staff (qualified in accordance with company procedures) and NDT personnel qualified in accordance with 145.A.30(f).
In this case the NDT inspector performs the NDT task and signs off the work order. The engine certifying staff releases the works performed to the engine (including NDT inspection) on an EASA Form 1.
Components
Class C
The release of the component maintenance carried out under C class rating has to be performed by components certifying staff (CCS).
The certifying staff is qualified following the procedures established by the organisation in compliance with the competent authority requirements. The CCS is not required to have a Part-66 licence.
The release of works performed under class C is done on an EASA Form 1 (or by means of an internal release document when this component is for the organisation’s own use and the organisation has in place the related internal procedures in the MOE).
A Part-145 organisation holding a C rating approval on a particular component and having in its approved scope of work NDT inspections for this component.
This organization needs to have CCS and NDT personnel qualified in accordance with 145.A.30(f).
In this case the NDT inspector performs the NDT task and signs off the Work Order / Engineering Order. The CCS releases the works performed to the component (including NDT inspection) on an EASA Form 1.
The certifying staff is qualified following the procedures established by the organisation in compliance with EN4179, Part-66 licence is not required.
The release of works performed under class D1 rating is done on an EASA Form 1 or using another form of release to service (other than aircraft release to service) as defined by the organisation in the MOE in compliance with 145.A.50 and approved by the competent authority.
A Part-145 organisation holding a D1 approval on a particular NDT method. The approved scope of work will be NDT inspections on this method.
This organisation needs to have NDT certifying staff qualified in accordance with 145.A.30(f).
In this case the NDT certifying staff performs and releases the NDT task on an EASA Form 1 or using another form of release to service (other than aircraft release to service) as defined by the organisation in the MOE in compliance with 145.A.50 and approved by the competent authority.
Note: In case of non-EU organisations approved by the EASA in accordance with Part-145, the Part-66 licence could be read as “Part-66 or national licence in accordance with Part-145 Appendix IV”
Part-CAO:
Certifying staff required
General Release procedure
Release procedure for an NDT inspection
Aircraft
(class aeroplanes, helicopter, airships, balloons or sailplanes)
The release of the aircraft maintenance carried out under A class rating has to be performed by certifying staff holding a Part-66 licence.
Licencing of personnel has to follow Part-66 regulation.
The release is either on the aircraft technical log or issuing an aircraft release to service statement.
A Part-CAO organisation holding an aeroplanes, helicopter, airships, balloons or sailplanes particular aircraft type or and having in its approved scope of work NDT inspections for this aircraft type.
This organization needs to have part-66 certifying staff and NDT personnel qualified in accordance with CAO.A.035(f).
In this case the NDT inspector performs the NDT task and signs off the work order. The aircraft is released by appropriately qualified B1, B3 or L certifying staff under the organisation’s aeroplanes, helicopter, airships, balloons or sailplanes rating.
Please note that the release may include not only the NDT task but also the associated tasks (removal of panels, blankets, wires, re-installation, etc), or the NDT task may be part of a base maintenance check.
Engines or Components other than complete engines
Class Components
The release of the engine maintenance carried out under components class rating has to be performed by ‘engine’s’ or ‘components other than complete engines‘ certifying staff.
The certifying staff is qualified following the procedures established by the organisation, Part-66 licence is not required.
The release of works performed under class components is done on an EASA Form 1 (or by means of an internal release document when this component is for the organisation’s own use and the organisation has in place the related internal procedures in the CAE).
A Part-CAO organisation holding a components rating approval on a particular engine type or ‘components other than complete engines‘ and having in its approved scope of work NDT inspections for this engine type.
This organization needs to have “engine” or ‘components other than complete engines‘ certifying staff (qualified in accordance with company procedures) and NDT personnel qualified in accordance with CAO.A.035(f).
In this case the NDT inspector performs the NDT task and signs off the work order. The engine or ‘components other than complete engines‘ certifying staff releases the works performed to the engine or ‘components other than complete engines‘ (including NDT inspection) on an EASA Form 1.
Components
Class C
The release of the component maintenance carried out under C class rating has to be performed by components certifying staff (CCS).
The certifying staff is qualified following the procedures established by the organisation in compliance with the competent authority requirements. The CCS is not required to have a Part-66 licence.
The release of works performed under class C is done on an EASA Form 1 (or by means of an internal release document when this component is for the organisation’s own use and the organisation has in place the related internal procedures in the MOE).
A Part-145 organisation holding a C rating approval on a particular component and having in its approved scope of work NDT inspections for this component.
This organization needs to have CCS and NDT personnel qualified in accordance with 145.A.30(f).
In this case the NDT inspector performs the NDT task and signs off the Work Order / Engineering Order. The CCS releases the works performed to the component (including NDT inspection) on an EASA Form 1.
The certifying staff is qualified following the procedures established by the organisation in compliance with EN4179, Part-66 licence is not required.
The release of works performed under class ‘Specialised Services’ rating is done on an EASA Form 1 or using another form of release to service (other than aircraft release to service) as defined by the organisation in the CAE in compliance with CAO.A.070(a) and approved by the competent authority (AMC1 CAO.A.070 (a)(1)).
A Part-CAO organisation holding a ‘Specialised Services’ approval on a particular NDT method. The approved scope of work will be NDT inspections on this method.
This organisation needs to have NDT certifying staff qualified in accordance with CAO.A.035(f).
In this case the NDT certifying staff performs and releases the NDT task on an EASA Form 1 or using another form of release to service (other than aircraft release to service) as defined by the organisation in the CAE in compliance with CAO.A.070 and approved by the competent authority.
Note: In case of non-EU organisations approved by the EASA in accordance with Part-145, the Part-66 licence could be read as “Part-66 or national licence in accordance with Part-145 Appendix IV”
Was this helpful?
Maintenance data
Shall the maintenance data be available and controlled at all times, even if there is no maintenance work going, or shall it be available only during the performance of maintenance?
Maintenance data has direct influence on many processes of the approved maintenance organisation (AMO) and contributes to demonstrate the overall capability of the organisation to perform maintenance.
The maintenance data either can be arranged directly by the AMO or provided by the customer/operator as specified by 145.A.45(a), M.A.609 or CAO.A.055(a). In both cases, the AMO should demonstrate that the maintenance data used, regardless of the source, is up-to-date. To discharge this responsibility, a procedure should be established to:
(a) control the amendment status of any documents being used;
(b) regularly check that all amendments are being received, e.g. by subscribing to a document amendment scheme (sufficient in case of direct access to the maintenance data through the DAH/OEM. The subscription to the maintenance data distribution system of the customer/operator is insufficient, additional independent verifications through the original author shall be done).
When the maintenance data is arranged directly by the AMO it shall be available and controlled continuously.
There are certain situations when the maintenance data can be obtained only through the customer/operator. One of the examples would be the maintenance data for the large aircraft. The maintenance data coming from the TC holder is usually customised because of the model/configuration/modification/order of aircraft, so it is normally not possible for the AMO to have this customised maintenance data directly from TC holder without having an aircraft of that type under the contract.
When the maintenance data is provided by the customer/operator, it shall be held and controlled by the AMO during maintenance on the concerned aircraft/component. Whenever the maintenance data is not available or not current, the maintenance shall not be performed and released.
Additionally, as part of the obligation for maintenance records, used maintenance data shall be:
to demonstrate that the organisation worked in compliance with their respective requirements.
Was this helpful?
Personnel requirements
Can a certification maintenance requirement (CMR) be performed by the Flight Crew before flight?
Normally the flight crew should not release CMR task unless that task is included in a “repetitive pre-flight airworthiness directive” under the conditions of 145.A.30(j)(3), M.A.606(h)(1) or CAO.A.040(c)(1)
In case of aircraft operated away from a supported location, the provisions of 145.A.30(j)(4), M.A.606(h)(2) or CAO.A.040(c)(2) could be used for CMRs as long as all the applicable conditions are met. In particular:
the task is considered “minor maintenance or a simple check” (AMC 145.A.30(j)(4) point 2(i) or AMC M.A.606(h)(2) point 2).
Was this helpful?
What is the meaning of the Protected Rights in the Appendix IV to Part-145?
The protected rights mentioned in paragraph 2(a) of the Appendix IV to Part-145 were included in the Regulation 2042/2003 for the persons who were already working in a Part-145 organisation in a location situated outside the EU before the entry into force of Part-66. These protected rights allowed those persons to continue exercising (inside that particular Part-145 organisation) the privileges of the certification authorisation issued by that Part-145 organisation without the need to comply with paragraphs 1(c) to 1(f).
If this person changed the employment to a different Part-145 approved organisation after the entry into force of Part-66 (i.e. 28 November 2003), the previous certification authorisation is not valid and he/she needs to receive a new one from the new Part-145 approved organisation. In this case paragraph 2 of Appendix IV is not applicable anymore.
This implies that any new or extended authorisation granted by AMOs to their C/S after the entry into force of Part-66 must comply with paragraphs 1(c) to 1(f) in particular regarding the type training certificates.
Was this helpful?
What are the training requirements for personnel within a Part-145 organisation, other than those contained in Part-66?
Requirement
Reference
The accountable manager shall demonstrate a basic understanding of Part-145.
The person or group of persons nominated responsible for ensuring that the organisation complies with Part-145 (including the Quality Manager) shall be able to demonstrate
The organisation shall establish and control the competence of personnel involved in any maintenance, airworthiness review management and/or quality audits in accordance with a procedure and to a standard agreed by the competent authority.
In addition to the necessary expertise related to the job function, competence must include an understanding of the application of human factors and human performance issues appropriate to that person’s function in the organisation.
This should include also:
145.A.30(e) and associated AMC/GM.
Appendix IV to AMC 145.A.30(e) and 145.B.10(3).
The organisation shall ensure that personnel who carry out and/or control a continued airworthiness non-destructive test of aircraft structures and/or components are appropriately qualified for the particular non-destructive test in accordance with the European or equivalent Standard recognised by the Agency.
Personnel who carry out any other specialised task shall be appropriately qualified in accordance with officially recognised Standards.
By derogation to this paragraph those personnel specified in paragraphs (g) and (h)(1) and (h)(2), qualified in category B1, B3 or L in accordance with Annex III (Part-66) may carry out and/or control colour contrast dye penetrant tests.
145.A.30(f) and AMC 145.A.30(f).
By derogation to paragraphs (g) and (h), in relation to the obligation to comply with Annex III (Part-66), the organisation may use certifying staff qualified in accordance with the following provisions:
1. For organisation facilities located outside the Community territory certifying staff may be qualified in accordance with the national aviation regulations of the State in which the organisation facility is registered subject to the conditions specified in Appendix IV to this Part.
2. For line maintenance carried out at a line station of an organisation which is located outside the Community territory, the certifying staff may be qualified in accordance with the national aviation regulations of the State in which the line station is based, subject to the conditions specified in Appendix IV to this Part.
3. For a repetitive pre-flight airworthiness directive which specifically states that the flight crew may carry out such airworthiness directive, the organisation may issue a limited certification authorisation to the aircraft commander and/or the flight engineer on the basis of the flight crew licence held. However, the organisation shall ensure that sufficient practical training has been carried out to ensure that such aircraft commander or flight engineer can accomplish the airworthiness directive to the required standard.
4. In the case of aircraft operating away from a supported location the organisation may issue a limited certification authorisation to the commander and/or the flight engineer on the basis of the flight crew licence held subject to being satisfied that sufficient practical training has been carried out to ensure that the commander or flight engineer can accomplish the specified task to the required standard. The provisions of this paragraph shall be detailed in an exposition procedure.
5. In the following unforeseen cases, where an aircraft is grounded at a location other than the main base where no appropriate certifying staff are available, the organisation contracted to provide maintenance support may issue a one-off certification authorisation:
(i) to one of its employees holding equivalent type authorisations on aircraft of similar technology, construction and systems; or
(ii) to any person with not less than five years maintenance experience and holding a valid ICAO aircraft maintenance licence rated for the aircraft type requiring certification provided there is no organisation appropriately approved under this Part at that location and the contracted organisation obtains and holds on file evidence of the experience and the licence of that person.
All such cases as specified in this point shall be reported to the competent authority within seven days of the issuance of such certification authorisation. The organisation issuing the one-off authorisation shall ensure that any such maintenance that could affect flight safety is re-checked by an appropriately approved organisation.
145.A.30(j) and associated AMC/GM.
Appendix IV to Part-145.
In addition to the appropriate requirements of 145.A.30(g) and (h), the organisation shall ensure that certifying staff and support staff have an adequate understanding of the relevant aircraft and/or components, or both, to be maintained and of the associated organisation procedures. In the case of certifying staff, this shall be accomplished before the issue or reissue of the certification authorisation.
145.A.35(a) and AMC 145.A.35(a).
The organisation shall ensure that all certifying staff and support staff are involved in at least six months of actual relevant aircraft or component maintenance experience in any consecutive two-year period.
145.A.35(c) and AMC 145.A.35(c).
The organisation shall ensure that all certifying staff and support staff receive sufficient continuation training in each two-year period to ensure that such staff have up-to-date knowledge of relevant technology, organisation procedures and human factor issues.
145.A.35(d) and AMC 145.A.35(d).
The organisation shall establish a programme for continuation training for certifying staff and support staff, including a procedure to ensure compliance with the relevant paragraphs of 145.A.35 as the basis for issuing certification authorisations under this Part to certifying staff, and a procedure to ensure compliance with Annex III (Part 66).
145.A.35(e) and AMC 145.A.35(e).
Except where any of the unforeseen cases of 145.A.30(j)(5) apply, the organisation shall assess all prospective certifying staff for their competence, qualification and capability to carry out their intended certifying duties in accordance with a procedure as specified in the exposition prior to the issue or reissue of a certification authorisation under this Part.
145.A.35(f) and AMC 145.A.35(f).
The holder of a category A aircraft maintenance licence may only exercise certification privileges on a specific aircraft type following the satisfactory completion of the relevant category A aircraft task training carried out by an organisation appropriately approved in accordance with Annex II (Part-145) or Annex IV (Part-147). This training shall include practical hands on training and theoretical training as appropriate for each task authorised. Satisfactory completion of training shall be demonstrated by an examination or by workplace assessment carried out by the organisation.
145.A.35(n) and AMC 145.A.35(n).
The holder of a category B2 aircraft maintenance licence may only exercise the certification privileges described in point 66.A.20(a)(3)(ii) of Annex III (Part-66) following the satisfactory completion of (i) the relevant category A aircraft task training and (ii) six months of documented practical experience covering the scope of the authorisation that will be issued. The task training shall include practical hands on training and theoretical training as appropriate for each task authorised. Satisfactory completion of training shall be demonstrated by an examination or by workplace assessment. Task training and examination/assessment shall be carried out by the maintenance organisation issuing the certifying staff authorisation. The practical experience shall be also obtained within such maintenance organisation.
145.A.35(o) and AMC 145.A.35(o).
Pre-flight inspections (when the 145 organisation has an agreement with an operator)
It should be demonstrated that the personnel carrying out pre-flight inspections have received appropriate training for the relevant pre-flight inspection tasks based on the operator’s CAME.